Gamme de produits

Söll GlideLoc Vertical Height Access System

The Söll GlideLoc® Safe Climbing system includes fall protection ladders, guide rails, and guided type fall arresters. System accessories such as entry and exit devices, roof ascent or shaft entry equipment make it possible to design a system that is not only appropriate for the structure of the building or installation, but which also satisfies the very highest safety requirements.

 

Codes article

Details FR

YA4-(ladder length in mm)

Y-SPAR - YA4 stainless steel
Simple, cost-effective, versatile safety ladder; Low surface area: keeps wind loads applied to the sub-structure to a minimum; also available with perforated rungs for applications in dirty environments; step width per side: 150 mm

YST-(ladder length in mm)

Y-SPAR - YST galvanised steel
Same specifications as Y-SPAR - YA4, however made of galvanised steel

YAL-(ladder length in mm)

Y-SPAR - YAL aluminium
Same specifications as Y-SPAR - YA4, however made of aluminium

ZA4(ladder length in mm)

Twin ladder - ZA4 stainless steel
Operator can glide his hands along the side rails; ideal for dirty environments; high distortion resistance; step width per side: 150 mm

ZST(ladder length in mm)

Twin ladder - ZST galvanised steel
Same specifications as Twin ladder - ZA4, however made of galvanised steel

ZAL-(ladder length in mm)

Twin ladder - ZAL aluminium
Same specifications as Twin ladder - ZA4, however made of aluminium

17440 / 1027668

Connector - aluminium
With safety cover plate; to connect aluminium Y-ladders; complete with all mounting screws; included in the delivery of each Y-ladder; must be used when an existing ladder is cut and reconnected

17370 / 1027863

Connector - galvanised steel
Same specifications as aluminium connector, however made in galvanized steel

17534

Replacement rung for Y-spar 150mm - aluminium
To replace damaged rungs on Y-spar and twin ladders; includes one rung and mounting material

17657

Replacement rung for Y-spar 180mm - aluminium
Same specifications as replacement rung with ref. 17534, however for 180mm

25660

Replacement rung for Twin 150mm - aluminium
Same specifications as replacement rung with ref. 17534, however for twin ladders

25661

Replacement rung rung for Twin 180mm -aluminium
Same specifications as replacement rung with ref. 17534, however for twin ladders 180mm.

26026 / 1030291

Bottom/Top End Stop, breaking load 12kN for aluminium ladders
For profile 52x51 mm, made of stainless steel; prevent the fall arrester from being inserted incorrectly or accidentally slipping out of the guide rail; supply of all fixings possible

26027 / 1030292

Bottom/Top End Stop, breaking load 12kN for steel/stainless steel ladder and aluminium guide rail
Same specifications as bottom/top end stop with ref. 26026, however for steel ladders and aluminium guide rail with profile 52x33mm, 50x32mm

11634 / 1007733

Fixed end stop
Same specifications as bottom/top end stop with ref. 26026, however a rigid end stop does not allow the fall arrester being taken out of the final top ladder section

27138 / 1033231

End-stop, top/bottom on the side
Same specifications as bottom/top end stop with ref. 26026, however used for ladder projection < 150 mm; mounting with reinforcement

14673 / 1008093

Open bracket - aluminium - Projection: 150 mm
Comes with stainless steel installation elements for fixing ladder to bracket; wall attachment must be drilled to suit site conditions; minimum bolt diameter for wall fixing: M16; custom made projections upon request

10566 / 1027683

Closed bracket - aluminium - Projection 150 mm
Same specifications as for the Open bracket, however closed and with variable mounting distance possible by moving and turning the bracket as required

21443 / 1027686

Closed bracket - aluminium Projection 220 mm
Same specifications as closed bracket with ref. 10566, however with projection of 220mm

10521 / 1027687

Brackets - aluminium
Consists of two bracket halves; complete with mounting elements for fixing to ladder; wall attachment must be drilled to suit site conditions; minimum bolt diameter 2 x M12; mounting distance on brickwork: 560mm

BB-VSTS(projection)

Bracket - galvanised steel- with adjustable projection
Used where ladder bends; mounting on catch bar; complete with all ladder mounting elements; wall attachment must be drilled to suit site conditions; minimum bolt diameter: M16

BS-STS-(Ø in mm)

Clamp - galvanised steel
Projection up to 1000 mm possible; complete with mounting elements for fixing to ladder; exact mast diameter and projection has to be indicated; mast diameter: min. 60 mm, max. 1500 mm

BS-A4S-(Ø in mm)

Clamp - stainless steel
Same specifications as the galvanized steel clamp, however in stainless steel

BS-VSTS-(Ø in mm)

Clamp - galvanised steel - with adjustable projection
Used where ladder bends; complete with all ladder mounting elements; exact mast diameter and projection has to be indicated; mast diameter: min. 60 mm, max. 1500 mm; projection ranges: L = 250 - 325 mm L = 326 - 400 mm L = 401 - 475 mm

20848 / 1027718

Weld-on bracket - galvanised steel - projection: 150 mm
To be welded on site; complete with all mounting elements; Attention: structure must be suitable for welding

11226 / 1027719

Bracket - galvanised steel - projection: 150 mm
For use on tube structures of 20 - 70 mm diameter; complete with all mounting elements; support structure must be checked to ensure sufficient strength; exact tube diameter must be indicated

BB-DA

Mounting element - galvanised steel- for exterior of corner strut
For diagonal struts on lattice masts on the exterior of the corner strut; complete with all mounting elements; strut width must be indicated

BB-DI

Mounting element - galvanised steel- for interior of corner strut
Same specifications as the mounting element with ref. BB-DA, however for the interior of the corner strut

BB-DK

Mounting element - galvanised steel
For crossings of diagonal struts on lattice masts; complete with all mounting elements; strut width and any filler plate measurements must be indicated

23722 / 1027731

Folding footrest - galvanised steel- for Y-spar and twin ladders
Complies with DIN 18799; for Y-spar and twin ladders with step widths of 150 and 180 mm; rung distance: 280 mm; recommended mounting distance: 10 m; complete with all mounting elements

26503

Folding footrest - stainless steel - for Y-spar and twin ladders
Same specifications as the folding footrest with ref. 23722, however in stainless steel.

23980

Folding footrest - galvanised steel - for climbways
Same specifications as the folding footrest with ref. 23722, however for climbways with reinforcement

24032

Folding footrest - galvanised steel- for aluminium ladders
Same specifications as the folding footrest with ref. 23722, however for aluminium ladders with profile 50 x 50mm

26534 / 1027732

Folding Footrest and platforms - galvanised steel
With foldable working platforms on both sides to provide working access adjacent to the ladder; mounted to the guide rail and mast at the same time; for use by one person only; complete with all mounting elements; rung distance: 280 mm; step width: 150 and 180 mm; mast diameter and projection must be indicated; stainless steel available upon request

26543 / 1027733

Folding Footrest and lefthand platform - galvanised steel
Same specification as folding footrest with platforms, however with only a foldable working platform on the left side

26545 / 1027734

Folding Footrest and righthand platform - galvanised steel
Same specification as folding footrest with platforms, however with only a foldable working platform on the right side

15391 / 1027735

Folding footrest- hinge on left side - galvanised steel
Pivotable; for all aluminium Y-spar and twin ladders; complete with all mounting elements

16547 / 1027736

Folding footrest - hinge on right side -galvanised steel
Pivotable; for all aluminium Y-spar and twin ladders; complete with all mounting elements

16124 / 1028002

Pivotable footrest - galvanized steel
For mounting on step irons with a diameter of max. 20 mm; complete with all mounting elements

18008 / 1028003

Pivotable footrest - stainless steel
For mounting on step irons with a diameter of max. 20 mm; complete with all mounting elements

21516 / 1028004

Footrest with hinge on left side - galvanised steel for GlideLoc guide rails
Pivotable; for mounting on side rails with a width of max. 50 mm; complete with all mounting elements

21520 / 1028006

Footrest with hinge on right side - galvanised steel for GlideLoc guide rails
Pivotable; for mounting on side rails with a width of max. 50 mm; complete with all mounting elements

23724 / 1016231

Folding footrest for GlideLoc guide rails
Complies with DIN 18799; complete with all mounting elements; clearance of at least 220 mm between rungs; rung diameter: max. 30 mm

mark with 'A'

Recess
To insert and take out the fall arresters; as the fall protection unit does not have a protective function within the recess, there must be an end-stop (ordered separately) attached above the recess; at the time of ordering, the part of the ladder with a recess must be marked with an ‘A’ or the notice ‘with recess’

10550 / 1027738

Exit section - aluminium - for Y-spar and twin ladders
To be installed within the climbway; to remove or insert the fall arrester; comes with single-use mounting tool; Attention: installation is only possible between two rungs

11317 / 1007743

Exit section - galvanized steel
To be installed within the climbway to remove or insert the fall arrester; comes with single-use mounting tool; For steel/stainless steel ladders and guide rails installation is only possible between two rungs; For GlideLoc guide rails rung distance: min. 250 mm, max. 320 mm; rung diameter: max. 24 mm

16978 / 1011795

Exit section - stainless steel
Same specifications as galvanized exit section, however made in stainless steel

21814 / 1027739

Rotary exit section without footrest - aluminium - for aluminium ladders
Used for leaving or entering the ladder system safely onto or from the platform behind the ladder; rotary exit section can be turned left or right; the top two rungs of the last ladder section must be removed; factory assembly on ladder section on demand (16604 / 1027938)

10558 / 1007114

Rotary exit section with footrest -aluminium - for aluminium ladders
Same specifications as rotary exit section ref. 21814, however with footrest that has two individually foldable platforms

16666 / 1027937

Rotary exit section without footrest -aluminium - for steel/stainless steel ladders
Same specifications as rotary exit section ref. 21814, however for steel/stainless steel ladders

17053 / 1007115

Rotary exit section with footrest -aluminium - for steel/stainless steel ladders
Same specifications as rotary exit section ref. 16666, however with footrest

HV-AL-(length in mm)

Reinforcement - aluminium - for aluminium ladders
Required when the distance between last mounting point and the top end of the ladder exceeds 525 mm; must be bolted onto the profile every 560 mm; must extend down over at least two mounting brackets; complete with all mounting elements; for Y-spar and twin ladders; square tube 50 x 50 x 4 mm

HV-ST-(length in mm)

Reinforcement - galvanized steel - for steel/stainless steel ladders
Required when the distance between last mounting point and the top end of the ladder exceeds 380 mm; must be bolted onto the profile every 560 mm; must extend down over at least two mounting brackets; complete with all mounting elements; square tube 50 x 30 x 3 mm

HV-A4-(length in mm)

Reinforcement - stainless steel - for steel/stainless steel ladders
Same specifications as reinforcement with ref. HV-ST, however in stainless steel

23144 / 1027741

Pivoting roof exit with hinge on left side - galvanised steel - for aluminium ladders
To be used in confined spaces; used for leaving or entering the ladder system safely onto or from the platform behind the ladder; complete with all mounting elements; to be fixed on the central spar of the ladder; top ladder section must be at least 1400 mm long

24946

Pivoting roof exit with hinge on right side - galvanised steel - for aluminium ladders
Same specifications as pivoting roof exit with ref. 23144, however with hinge on the right side

23312 / 1027939

Pivoting roof exit with hinge on left side - galvanised steel - for steel/stainless steel ladders
Same specifications as pivoting roof exit with ref. 23144, however for steel/stainless steel ladders

26772

Pivoting roof exit with hinge on right side - galvanised steel - for steel/stainless steel ladders
Same specifications as pivoting roof exit with ref. 23312, however with hinge on the right side

21683 / 1027742

Aluminium cover plate with hinge on left side - for Y-spar and twin ladders
Without ladder section; prevents unauthorised people from climbing the front or the rear of the ladder; brackets are covered as well (up to projection 150 mm); opens laterally; hinges can be switched on site; stainless steel fixings; cylinder lock; plate length: 2500 mm; width: 523 mm; width when cover plate is open: 991 mm; factory assembly on a ladder section (16368 / 1027744); replacement key (17478 / 1027745); installation above normal height - Hinge on left side (21684 / 1027746); installation above normal height - Hinge on right side (21685 / 1027747)

21759 / 1027743

Aluminium cover plate with hinge on right side - for Y-spar and twin ladders
Same specifications as aluminium cover plate with ref. 21683, however with hinge on right side

21684 / 1027746

Aluminium cover plate installed above normal height with hinge on left side - for Y-spar and twin ladders
Same specifications as aluminium cover plate with ref. 21683, however with installation above normal height

21685 / 1027747

Aluminium cover plate installed above normal height with hinge on right side - for Y-spar and twin ladders
Same specifications as aluminium cover plate with ref. 21684, however with hinge on right side

11354 / 1007740

Steel cover plate - for aluminium ladders with step width 150 mm
Without ladder section; prevents unauthorised people from climbing the ladder; can be mounted and must be secured with a padlock; length: 2000 mm

10531 / 1027749

Cable holder - aluminium
To retain cables behind ladders and guide rails; complete with all mounting elements; for use on tubular masts or corner struts; if loaded equally, a cable holder can carry a max. of 12.5 kg; the total load of the cables must not exceed 35 kg/m

15299 / 1027750

Turntable with bending radius of horizontal guide rail > 1000 mm - stainless steel - for aluminium ladders
For safe transfer from vertical to horizontal and vice versa; with aluminium profile for supporting the fall arrester; factory assembly on an aluminium Y-spar ladder (16884 / 1027752)

20793 / 1027751

Turntable with bending radius of horizontal guide rail < 1000 mm - stainless steel - for aluminium ladders
Same specifications as the turntable with ref. 15299, however with bending radius < 1000mm

11607 / 1027932

Turntable with bending radius of horizontal guide rail > 1000 mm - stainless steel - for steel/stainless steel ladders
Same specifications as the turntable with ref. 15299, however for steel/stainless steel ladders

20349 / 1028007

Turntable with bending radius of horizontal guide rail < 1000 mm - stainless steel - for steel/stainless steel ladders
Same specifications as the turntable with ref. 11607, however with bending radius < 1000mm

22322 / 1007134

Ho-Ver turntable - stainless steel
For safe transfer from vertical to horizontal and vice versa; the direction of travel can only be changed to the left or to the right

22495 / 1027933

Ho-Ver turntable with release option -stainless steel
Same specifications as the standard ho-ver turntable, however with release option in the pivoting part

22300

Turntable holder - galvanised steel
Holder for turntable mounting; alternative solution for mounting turntable with four brackets; complete with spacers and mounting elements; for mounting a turntable on a Söll GlideLoc steel ladder

17410 / 1027775

Manhole entry device - aluminium
For safe entry into manholes; only use together with lower part for manhole entry device; this device can be moved from one manhole ladder to another and can be locked

17065 / 1014667

Manhole entry device - stainless steel
Same specifications as the aluminium manhole entry device, however in stainless steel

16191 / 1014666

Lower part for manhole entry device - stainless steel
Fixed to the rear of the fixed guide rail; for both aluminium and stainless steel manhole entry devices

16612 / 1027776

Roundabout - galvanised steel - for aluminium ladders with mast diameter 200 to 350 mm
For safe transfer between two different offset climbways; projection of the climbways must be the same; mast diameter: min. 200 mm / max. 1000 mm; max. rotation angle: 200°; comprising parallel rods and carriage for offsetting the fall arrester; comes with all fixing elements; diagrams specifying the mast diameter, climbway offset angle, projection, ladder type and direction of rotation must be provided; mast diameter 200 to 350 mm (16612 / 1027776); mast diameter 351 to 500 mm (18697 / 1027777); mast diameter 501 to 700 mm (18698 / 1027778); mast diameter 701 to 1000 mm (18699 / 1027779)

18697 / 1027777

Roundabout - galvanised steel - for aluminium ladders with mast diameter 351 to 500 mm
Same specifications as the roundabout with ref. 16612, however for mast diameter of 351 to 500mm

18698 / 1027778

Roundabout - galvanised steel - for aluminium ladders with mast diameter 501 to 700 mm
Same specifications as the roundabout with ref. 16612, however for mast diameter of 501 to 700mm

18699 / 1027779

Roundabout - galvanised steel - for aluminium ladders with mast diameter 701 to 1000 mm
Same specifications as the roundabout with ref. 16612, however for mast diameter of 701 to 1000mm

16352 / 1027945

Roundabout - galvanised steel - for steel/stainless steel ladders mast diameter 200 to 350 mm
For safe transfer between two different offset climbways; projection of the climbways must be the same; mast diameter: min. 200 mm / max. 1000 mm; max. rotation angle: 200°; comprising parallel rods and carriage for offsetting the fall arrester; comes with all fixing elements; diagrams specifying the mast diameter, climbway offset angle, projection, ladder type and direction of rotation must be provided; mast diameter 200 to 350 mm (16352 / 1027945); mast diameter 351 to 500 mm (18700 / 1027946); mast diameter 501 to 700 mm (18701 / 1027947); mast diameter 701 to 1000 mm (18702 / 1027948)

18700 / 1027946

Roundabout - galvanised steel - for steel/stainless steel ladders mast diameter 351 to 500 mm
Same specifications as roundabout with ref. 16352, however for mast diameter 351 to 500mm

18701 / 1027947

Roundabout - galvanised steel - for steel/stainless steel ladders mast diameter 501 to 700 mm
Same specifications as roundabout with ref. 16352, however for mast diameter 501 to 700 mm

18702 / 1027948

Roundabout - galvanised steel - for steel/stainless steel ladders mast diameter 701 to 1000 mm
Same specifications as roundabout with ref. 16352, however for mast diameter 701 to 1000 mm

UP-(segment size)-(Ø in mm)

Transfer platform - galvanised steel
Can be used individually or with roundabout; complete with all mounting elements; diagrams specifying the mast diameter, position of the climbways and size of the segment (90°, 180° or 270°)must be provided; mast diameter: min. 100 mm / max. 1000 mm

10779 / 1027814

Mounting bracket with insertion aid for projection: 130 mm - galvanised steel
For use in mast clamp without lock (BES-OA); complete with mounting elements for fixing to ladder

18065

Mounting bracket with insertion aid for projection: 150 mm - galvanised steel
For use in mast clamp without lock (BES-OA); complete with mounting elements for fixing to ladder

14981 / 1027815

Bracket for mast clamp with lock - projection: 130 mm - galvanised steel
For use in mast clamp with lock (BES-MA); complete with mounting elements for fixing to ladder

19646

Bracket for mast clamp with lock - projection: 150 mm - galvanised steel
For use in mast clamp with lock (BES-MA); complete with mounting elements for fixing to ladder

14982 / 1027816

Bracket for mast clamp without lock - projection: 130 mm - galvanised steel
For use in mast clamp without lock (BES-OA); complete with mounting elements for fixing to ladder

18068

Bracket for mast clamp without lock - projection: 150 mm- galvanised steel
For use in mast clamp without lock (BES-OA); complete with mounting elements for fixing to ladder; projection: 130 mm (14982 / 1027816); projection: 150 mm (18068)

15772 / 1027817

Fixed wall bracket - galvanised steel
For retention of insertion suspension ladder; lockable; with hole for padlock: Ø 11 mm (padlock not included in delivery)

BES-OA-(Ø in mm)

Mast clamp without lock - galvanised steel
Exact mast diameter and dimensions of rear edge of ladder to structure must be indicated; mast diameter: min. 80 mm / max. 1500 mm

BES-MA

Mast clamp with integrated lock - galvanised steel
Same specifications as mast clamp ref. BES-OA, however with integrated lock

18419 / 1027824

Mast clamp with projection - galvanised steel
Only for use in conjunction with connector (17261 / 1027827); projection depends on the type of fixed installation ladder (max. 170 mm); the following required information must be indicated: mast diameter, type of fixed installation ladder, bracket for fixed installation ladder, including projection; mast diameter: min. 60 mm / max. 220 mm

17261 / 1027827

Connector for insertion suspension ladder - galvanised steel
For connection onto mast clamp with projection (18419 / 1027824)using locking bolt; complete with mounting elements for fixing to ladder

16624 / 1027828

Connector - aluminium
For insertion suspension ladder - installation from below; for connection with fixed installation ladder; complete with mounting elements for fixing to ladder

BB-SSTR-(projection in mm)

Bracket - For steel/stainless steel ladders - galvanized steel
Complete with all ladder mounting elements; wall attachment must be drilled to suit site conditions; minimum bolt diameter: M16; projection in 5 mm increments from 70 mm to max. 280 mm available; variable mounting distance possible by moving and turning the bracket as required

BB-SA4R-(projection in mm)

Bracket - For steel/stainless steel ladders - stainless steel
Same specifications as bracket BB-SSTR, however made in stainless steel

BS-STR-(Ø in mm)

Clamp - For steel/stainless steel ladders - galvanized steel
Projection up to 1000 mm possible; complete with all mounting elements; exact mast diameter and projection must be indicated

BS-A4R-(Ø in mm)

Clamp - For steel/stainless steel ladders - stainless steel
Same specifications as clamp with ref. BS-STR, however made in stainless steel

11025 / 1027720

Angle corner mounting bracket for use on corner struts with angle profile up to 100 x 100 - galvanised steel
For use on corner struts of lattice masts with angle profile; complete with all mounting elements; support structure must be checked to ensure sufficient strength; for use on corner struts with angle profile up to 100 x 100 (11025 / 1027720); for use on corner struts with angle profile from 110 x 110 to 140 x 140 (14696 / 1027721); for use on corner struts with angle profile from 150 x 150 to 180 x 180 (14698 / 1027722); for use on corner struts with angle profile from 190 x 190 to 220 x 220 (14699 / 1027723); for use on corner struts with angle profile from 230 x 230 to 260 x 260 (14700 / 1027724)

14696 / 1027721

Angle corner mounting bracket for use on corner struts with angle profile from 110 x 110 to 140 x 140 - galvanised steel
Same specifications as angle corner mounting bracket ref. 11025, however for use on corner struts with angle profile from 110 x 110 to 140 x 140

14698 / 1027722

Angle corner mounting bracket for use on corner struts with angle profile from 150 x 150 to 180 x 180 - galvanised steel
Same specifications as angle corner mounting bracket ref. 11025, however for use on corner struts with angle profile from 150 x 150 to 180 x 180

14699 / 1027723

Angle corner mounting bracket for use on corner struts with angle profile from 190 x 190 to 220 x 220 - galvanised steel
Same specifications as angle corner mounting bracket ref. 11025, however for use on corner struts with angle profile from 190 x 190 to 220 x 220

14700 / 1027724

Angle corner mounting bracket for use on corner struts with angle profile from 230 x 230 to 260 x 260 - galvanised steel
Same specifications as angle corner mounting bracket ref. 11025, however for use on corner struts with angle profile from 230 x 230 to 260 x 260

11222 / 1013300

Clamp for round rungs - galvanised steel
For retrofitting safety ladders to support structures made of round tube steel; complete with all mounting elements; support structure must be checked to ensure sufficient strength

16601 / 1027887

Clamp for round rungs - stainless steel
Same specifications as clamp for round rungs ref. 11222, however made in stainless steel

24462

Clamp for square rungs - galvanised steel
For retrofitting safety ladders to support structures made of angle steel, U and hollow profiles; complete with all mounting elements; support structure must be checked to ensure sufficient strength

BB-VSTR(projection in mm)

Bracket - galvanised steel
With adjustable projection; complete with all ladder mounting elements; wall attachment must be drilled to suit site conditions; minimum bolt diameter: M16

12709 / 1027893

Bracket - galvanised steel
For use on tube structures of 20 - 70 mm diameter; complete with all mounting elements; support structure must be checked to ensure sufficient strength; exact diameter must be indicated

12732 / 1027894

Weld-on bracket for steel/stainless steel ladders - raw steel
To be welded on site; projection 150 mm; complete with all mounting elements; ensure structure is suitable for welding

16629 / 1027895

Weld-on bracket for steel/stainless steel ladders - galvanized steel
Same specifications as weld-on bracket with ref. 12732, however made in galvanized steel

16596 / 1027896

Weld-on bracket for steel/stainless steel ladders - stainless steel
Same specifications as weld-on bracket with ref. 12732, however made in galvanized steel

BB-VSTAD(projection in mm)

Mounting bracket with adapter - galvanised steel
With adjustable projection; used where ladder bends; complete with all ladder mounting elements; wall attachment must be drilled to suit site conditions; minimum bolt diameter: M16

16315 / 1010621

Twisted changeover rail - clockwise turn - galvanised steel
Guide rails with 90° bend allows transfer from vertical to horizontal direction; to be used only with Söll GlideLoc fall arresters included in the product range after March 2003; the guide rail is also turned 90° in the area of the bend; attachment is required for the horizontal rail area (not included in delivery); comes with connector, fixing cross and end-stop

16292 / 1027941

Twisted changeover rail - anticlockwise turn - galvanised steel
Same specifications as twisted changeover rail ref. 16315, however with anticlockwise turn

FS-SAL-(ladder length in mm)

Guide rail - aluminium
For vertical application; with connector; mounting distance: recommended 1400 mm - max. 1680 mm; max. section length: 4480 mm

FS-SST-(ladder length in mm)

Guide rail - galvanised steel
Same specifications as Guide rail FS-SAL, however made of galvanised steel

FS-SA4-(ladder length in mm)

Guide rail - stainless steel
Same specifications as Guide rail FS-SAL, however made of stainless steel

17372 / 1028024

Connector for steel guide rails - galvanized steel
To connect guide rails; complete with all mounting elements; included in the delivery of each guide rail

17988 / 1028025

Connector for steel and aluminium guide rails - stainless steel
To connect guide rails; complete with all mounting elements; included in the delivery of each guide rail

25589

Connector internal - stainless steel
Only for aluminium guide rails; to compensate for different lengths; gap width max. 50 mm

26791

Straight clamp for angle profiles - galvanised steel
For retrofitting guide rails on ladders with rungs made of angle steel; complete with all mounting elements

26761

Straight clamp for square/U-rungs - galvanised steel
Same specifications as straight clamp ref. 26791, however for square/U-rungs or hollow profiles

18861 / 1007950

Shim with d = 5 mm - galvanised steel
To compensate for different heights of individual rungs; clamping rail screw length must be adapted as necessary

18860 / 1027988

Shim with d = 3 mm - galvanised steel
To compensate for different heights of individual rungs; clamping rail screw length must be adapted as necessary

18863 / 1027989

Shim with d = 5 mm - stainless steel
To compensate for different heights of individual rungs; clamping rail screw length must be adapted as necessary

18862 / 1027990

Shim with d = 3 mm - stainless steel
To compensate for different heights of individual rungs; clamping rail screw length must be adapted as necessary

18859 / 1027991

Shim with d = 2 mm - stainless steel
To compensate for different heights of individual rungs; clamping rail screw length must be adapted as necessary

10903 / 1007735

Clamp with screw length M12 x 80 for rung diameter of 25 mm - galvanized steel
For retrofitting on ladders or step irons; complete with all mounting elements; support structure end/or wall mounting must be checked to ensure sufficient strength

14804 / 1013115

Clamp with screw length M12 x 90 for rung diameter 26-35mm - galvanized steel
Same specifications as galvanized steel clamp with ref. 10903, however with screw length M12 x 90 for rung diameter 26-35mm

14805 / 1027983

Clamp with screw length M12 x 100 for rung diameter 36-45mm - galvanized steel
Same specifications as galvanized steel clamp with ref. 10903, however with screw length M12 x 100 for rung diameter 36-45mm

14806 / 1027985

Clamp with screw length M12 x 110 for rung diameter 46-55mm - galvanized steel
Same specifications as galvanized steel clamp with ref. 10903, however with screw length M12 x 110 for rung diameter 46-55mm

14807 / 1007833

Clamp with screw length M12 x 120 for rung diameter 56-65mm - galvanized steel
Same specifications as galvanized steel clamp with ref. 10903, however with screw length M12 x 120 for rung diameter 56-65mm

14809 / 1011313

Clamp with screw length M12 x 70 for rung diameter of 25 mm - stainless steel
For retrofitting on ladders or step irons; complete with all mounting elements; support structure end/or wall mounting must be checked to ensure sufficient strength

14813 / 1016091

Clamp with screw length M12 x 80 for rung diameter 26-35mm - stainless steel
Same specifications as stainless steel clamp ref. 14809, however with screw length M12 x 80 for rung diameter 26-35mm

14814 / 1027984

Clamp with screw length M12 x 90 for rung diameter 36-45mm - stainless steel
Same specifications as stainless steel clamp ref. 14809, however with screw length M12 x 90 for rung diameter 36-45mm

14815 / 1027986

Clamp with screw length M12 x 100 for rung diameter 46-55mm - stainless steel
Same specifications as stainless steel clamp ref. 14809, however with screw length M12 x 100 for rung diameter 46-55mm

14816 / 1027987

Clamp with screw length M12 x 120 for rung diameter 56-70mm - stainless steel
Same specifications as stainless steel clamp ref. 14809, however with screw length M12 x 120 for rung diameter 56-70mm

11382 / 1027994

Standard clamp - galvanized steel
For mounting on existing safety ladders with side rails; complete with all mounting elements

16847 / 1027995

Standard clamp - stainless steel
For mounting on existing safety ladders with side rails; complete with all mounting elements

19091 / 1027996

Customized clamp - galvanized steel
For mounting on existing safety ladders with side rails; complete with all mounting elements

21284 / 1027997

Customized clamp - stainless steel
For mounting on existing safety ladders with side rails; complete with all mounting elements

23961

Clamp for mounting on I/U-supports - galvanized steel
When ordering please specify dimensions ‘h’ and ‘b’; only for use in conjunction with side end-stop (27136 / 1033231

26665

Clamp for mounting on I/U-supports - stainless steel
Same specifications as clamp with ref. 23961, however made in stainless steel

18363 / 1027998

Clamp for mounting on side rails - galvanised steel
For mounting on side rails with diameter 20 - 70 mm; complete with all mounting elements

26944

Rung bracket for rung dimensions 20x20mm
For mounting on aluminium ladders; complete with all mounting elements; for rung distance 280 mm only; other dimensions from 20 to 27mm available upon request

26826

Rung bracket for rung dimensions 21x21mm
Same specifications as rung bracket with ref. 26944, however for rung dimensions 21x21mm

27003

Rung bracket for rung dimensions 25x25mm
Same specifications as rung bracket with ref. 26944, however for rung dimensions 25x25mm

26189

Rung bracket for rung dimensions 25x34mm
Same specifications as rung bracket with ref. 26944, however for rung dimensions 25x34mm

26318

Rung bracket for rung dimensions 28x28mm
Same specifications as rung bracket with ref. 26944, however for rung dimensions 28x28mm

27367

Rung bracket for rung dimensions 29x29mm
Same specifications as rung bracket with ref. 26944, however for rung dimensions 29x29mm

25588

Rung bracket for rung dimensions 29x27mm
Same specifications as rung bracket with ref. 26944, however for rung dimensions 29x27mm

26067 / 1030952

Rung bracket for rung dimensions 30x30mm
Same specifications as rung bracket with ref. 26944, however for rung dimensions 30x30mm

25790 / 1030242

Rung bracket for rung dimensions 31x31mm
Same specifications as rung bracket with ref. 26944, however for rung dimensions 31x31mm

11319 / 1027992

Bracket for lateral mounting of guide rails on step irons - galvanized steel
Only for step irons with a diameter of 20 to 25 mm; complete with all mounting elements

17989 / 1027993

Bracket for lateral mounting of guide rails on step irons - stainless steel
Only for step irons with a diameter of 20 to 25 mm; complete with all mounting elements

11102 / 1027999

Bracket - galvanized steel
For mounting of horizontal guide rails; complete with all mounting elements; support structure must be checked to ensure sufficient strength

16838 / 1028000

Bracket - stainless steel
For mounting of horizontal guide rails; complete with all mounting elements; support structure must be checked to ensure sufficient strength

17228 / 1028001

Bracket - galvanised steel
For mounting on side rails from angle profile up to 50 x 50 mm; complete with all mounting elements

19876

Identification plate not engraved - aluminium
For fall protection device Söll GlideLoc fall protection systems; cover plate assembled in factory; must be affixed to each access point; languages D/E/F/ES

20854

Identification plate engraved for galvanized steel ladder - aluminium
Same specifications as ID plate with ref. 19876, however engraved for galvanized steel ladders

20855

Identification plate engraved for stainless steel ladder - aluminium
Same specifications as ID plate with ref. 19876, however engraved for stainless steel ladders

18072 / 1028075

Ice scraper
Removes frost and ice on the inside and outside of the running surfaces of the Söll GlideLoc guide rails; can be used for all profiles; anodised aluminium body; spring steel blades

27441 / 1033980

Coulisseaux anti-chute Söll BodyControl I
Conformes à la norme européenne EN 353-1:2014; Point d‘amarrage sternal; Arrête les chutes en toutes circonstances: vers le bas et en arrière; BodyControl I pour une ascension proche de l‘échelle; Avec un élément absorbeur d‘énergie; Mousqueton à triple action avec émerillon; Corps en aluminium, nez d‘accrochage en acier inoxydable

27440 / 1033981

Coulisseaux anti-chute Söll BodyControl II
Conformes à la norme européenne EN 353-1:2014; Points d‘amarrage sternal et ventral; Arrête les chutes en toutes circonstances: vers le bas et en arrière; BodyControl II pour une ascension avec une position du corps en arrière; Avec un élément absorbeur d‘énergie; Mousqueton à triple action avec émerillon; Corps en aluminium, nez d‘accrochage en acier inoxydable

23331 / 1027640

Söll Comfort 2 fall arrester
Base body, safety catch and self-locking safety karabiner are manufactured from saltwater-proof stainless steel

25805 / 1029249

Söll Universal II fall arrester
Complies with EN 353-1:2002 and CNB/P/11.073; can be inserted and removed at any position; self-closing swivel safety karabiner and three self-locking aluminium elements; for vertical and horizontal use in all Söll GlideLoc fall protection systems; fall arrester manufactured from stainless steel



Caractéristiques principales

Söll GlideLoc fall protection ladders have an integrated guide rail for the guided-type fall arrester in the centre stile. They are available in aluminum, galvanized or stainless steel both as central-stile ladders (Y-spar) and with side stiles (twin ladder).

  • Distance between rungs is 280mm. Customised designs may be available.
  • Durable construction for extended service life
  • Accommodates multiple workers

The easy-climb Söll GlideLoc guided type fall arrester offers hands-free safety at height that ultimately increases worker mobility, safety and productivity.

  • Guided type fall arrester is fixed by the karabiner hook to the D-ring of the full body harness and inserted into the guide rail
  • Engineered for smooth operation for ascending/descending, provides an easier, more comfortable climb

  • Automatic design – keeps both hands free for climbing

  • Stainless steel catch clamp – locks into the rail in the event of a fall

  • Integrated shock-absorbing mechanism – reduces force on the worker and system in the event of a fall

  • Fall indicator – alerts user to know when to remove the product from service

  • Integrated swivel, auto-locking carabiner connection – aids in trailing alignment and meets allowable attachment length

  • Design prevents up-side-down installation – increases worker safety by ensuring proper attachment

  • No requirement to lean back while climbing – reduces fatigue; ideal for ladder cages and confined spaces

  • Ergonomically designed for easy one-hand installation – increases productivity

     

Fall protection for the highest safety requirements

A safe climbing system must meet stringent safety standards and be resistant to wear and tear.

  • Söll GlideLoc guide rails allow a combination of vertical and horizontal access without having to disconnect and reconnect.
  • Rail systems permit safe roof and platform access.

 

Horizontal access to workplaces at height

The EN 795:2012 compliant GuideLoc anchorage device is based on guide rails and is designed to provide a safe working environment for people working at height such as on roofs. The worker wears a full body harness and uses a lanyard (or other connector compliant with EN 354/ EN 355) to connect to the eye of the shuttle, which travels along the rail. For overhead applications a retractable fall arrester can be used to provide the most effective means of protection.

 

Systems are available in easy-to-install kits or can be customized for your application with additional available components, including:

  • Brackets for larger ladder rungs
  • Brackets to attach to ladder side rails
  • Foldable foot rests for long ladders
  • Shaft entry device to provide easy access to manholes and roof hatches 

Ideal for:

  • Permanent Ladder Applications
  • Wind Power/Turbines
  • Telecommunications
  • Construction, buildings and facades
  • Utilities
  • Industrial Facilities / chimneys
  • Drilling Rigs/Platforms
  • Shipbuilding
  • Crane Installation
  • Confined Space
  • Loading bays

Réglementations

  • Meets the EN 353-1 and AS/NZS 1891 standards (and all applicable OSHA, ANSI and CSA standards)

Informations de garantie

We sincerely believe that our fall protection equipment is the best in the world. Our products endure rigorous test to ensure that the fall protection equipment you trust is manufactured to the highest standards. Miller fall protection products are tested to withstand normal wear and tear, but are not indestructible and can be damaged by misuse. Our Limited Lifetime Warranty does not apply to normal wear and tear or abusive treatment of the product. In the unlikely event that you should discover defects in either workmanship or materials, under our Limited Lifetime Warranty, we will repair or replace the product at our expense. If a replacement is necessary and your product is no longer available, a comparable product will be substituted. Should a product issue surface, contact us at +33 248 53 00 80 (Southern Europe) or +49 9281 8302 0 (Northern Europe). Manufacturing specifications are subject to change without notice.

Söll Comfort GlideLoc Fall Arrester

Attaches at top or bottom of rail

Söll Universal II GlideLoc Fall Arrester

Attaches anywhere on rail

Söll Comfort II GlideLoc Fall Arrester

Specially-designed for highly corrosive environments



Permanently installed climbing systems are tested and certified as a complete single system, including Söll guide rails, Söll fall arresters and Söll accessories. This means that, in a Söll GlideLoc® system only the Söll GlideLoc® fall arresters may be used. It is not permitted to use fall arresters from other manufacturers in these systems. Their use does comply with the regulations, hence, their functionality can not be guaranteed and in the event of an accident, Honeywell will not be liable.

 

Markings

The following is engraved on each Söll GlideLoc fall arrester:

  • Name of Manufacturer
  • Date of Manufacture and Serial number
  • CE-Label and Key-code of testing institute
  • Indication to read manual
  • Type of system
  • Relevant standard

Furthermore, an icon indicates to read the instruction manual before use. An arrow also indicates the correct direction of use. The date plate indicates when the next inspection is due.

Proper product training and professional fall protection training is recommended. Refer to Product Use Instructions enclosed with products.

Honeywell Safety Products France

ZI Paris Nord II
Immeuble Edison
33, rue des Vanesses
BP 55288 Villepinte
95958 Roissy CDG Cedex
+33 (0) 1 49 90 79 79
+33 (0) 1 49 90 71 04

    Contact >

    Liste de fiches techniques

    Cliquez sur cette icône pour afficher la liste des fiches techniques que vous souhaitez télécharger. Une fois validée, la liste sera enregistrée et accessible pendant cinq jours au maximum. Vous pouvez répertorier jusqu'à 20 éléments. Rappel : les listes non validées seront perdues lors de la fermeture de votre fenêtre de navigateur ou de votre déconnexion de Ma Sécurité.